1. Community Forum
  2. Audio Weaver® General
  3. About the error of "Target IO (awe_fwGetProfileValues)> 0x39E81C3F - FAILED"

About the error of "Target IO (awe_fwGetProfileValues)> 0x39E81C3F - FAILED"

6 posts / 0 new
Log in or register to post comments
Last post
Tue, 07/18/2023
10:03pm
yue.wang_10490
#1
Top
#1
About the error of "Target IO (awe_fwGetProfileValues)> 0x39E81C3F - FAILED"

Hi.

After connected to my target board with AWE,

I ran the signal flow. Every once in a while (15-20 minutes), the connection breaks.

From the log, you can see that the last message has the following Failed:

2023/07/17 11:35:44.910 RX-encoded  02 39 80 80 8C 80 80 B4 FF FF FF 8F B4 FF F3 FF 8F 03
2023/07/17 11:35:44.910 Target IO (awe_fwGetProfileValues)> 0x39E81C3F - FAILED

What is the reason for this?

Similar error messages include:

2023/07/17 11:46:55.572 RX-encoded  02 37 80 80 8C 80 80 B4 FF FF FF 8F B4 FF F3 FF 8F 03
2023/07/17 11:46:55.572 Target IO (awe_GetCallfwFetchValues)> 0x39E85BBF - FAILED

or

2023/07/17 11:49:04.384 RX-encoded  02 32 80 80 8C 80 80 B4 FF FF FF 8F B4 FF F3 FF 8F 03
2023/07/17 11:49:04.384 Target IO (awe_fwGetCallFetchValue)> 0x39E85B83 - FAILED

or

2023/07/19 09:49:01.586 RX-encoded  02 32 80 80 8C 80 80 B4 FF FF FF 8F B4 FF F3 FF 8F 03
2023/07/19 09:49:01.586 Target IO (awe_fwGetProfileValues)> 0x26054BF6 - FAILED

 

 

Image icon capture.png
Wed, 07/19/2023
4:20pm
DSPC_Gary
Top

Hi Yue,

Which interface are you using to connect to your board?

If it's the USB port, are you using a hub?  This could cause problems.

You might try setting the timeout value longer (or shorter, to see if the problem happens more frequently).

Thanks,

Gary

Thu, 07/20/2023
1:32am
yue.wang_10490
Top
(Reply to #2)

Hi Gary.

Thank you for your reply.

We are using the USB2UART interface(FTDI) connect PC with the ADI 2156x board.

You say the timeout value adjusted in AWE?

Thu, 07/20/2023
1:07pm
DSPC_Gary
Top

Hi Yue,

  • Where did you get the BSP for the 2156x (from DSPC or someone else)?
  • Can you attach a screenshot of your AWE Server RS232 Target Connection info, e.g.:

Thanks,

 

Gary

 

Thu, 07/20/2023
9:42pm
yue.wang_10490
Top
(Reply to #4)

Thanks Gary.
I tried modifying "Retries" the way you did and the problem has been solved.

Thank you very much.

 

Fri, 07/21/2023
11:10am
DSPC_Gary
Top

Great news, thanks for the update!

Gary